I recently installed Rockstor and really like what is going on here over the others out there the interface is great I see that it is relatively new so to speak but I have not been able to get SMART to get the data from the drives on the system.
I would like to see temps for disk and motherboard added to the dash board whn you guys get a chance if this is not already in the works
So to my issue, These are 8, 2 TB WD drives, on a 3ware LSI 9750-8i raid controller, with an ASUS MB and 16 gig of ram and a 240 gb SSD for a boot drive, the disk are not in a array the are all set as single disk, when I was testing the other systems nas4free and freenas i was able to get this to work or it appeared to work.
I get the error below when access this info in the web ui
S.M.A.R.T support is not available for this disk (sdh)
Testing some on CLI i get the following, which looks like start is available but disabled and I have not be able to enable this on the drive, any tips or hints where to go next? How can i get this working i really want to start using rockstor I think is a great product and heads above the rest out there so
smartctl -a /dev/sdb
smartctl 6.2 2013-07-26 r3841 [x86_64-linux-4.2.5-1.el7.elrepo.x86_64] (local build)
Copyright © 2002-13, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Vendor: LSI
Product: 9750-8i DISK
Revision: 5.12
User Capacity: 1,999,988,850,688 bytes [1.99 TB]
Logical block size: 512 bytes
Logical Unit id: 0x600050e042721600edba0000d14e0000
Serial number: omitted
Device type: disk
Local Time is: Wed Dec 23 22:44:44 2015 EST
SMART support is: Available - device has SMART capability.
SMART support is: Disabled
Temperature Warning: Disabled or Not Supported
=== START OF READ SMART DATA SECTION ===
SMART Health Status: OK
Error Counter logging not supported
Device does not support Self Test logging
lsblk
NAME MAJ:MIN RM SIZE RO TYPE MOUNTPOINT
sda 8:0 0 223.6G 0 disk
├─sda1 8:1 0 500M 0 part /boot
├─sda2 8:2 0 7.9G 0 part [SWAP]
└─sda3 8:3 0 215.2G 0 part /mnt2/rockstor_rockstor
sdb 8:16 0 1.8T 0 disk
sdc 8:32 0 1.8T 0 disk
sdd 8:48 0 1.8T 0 disk
sde 8:64 0 1.8T 0 disk
sdf 8:80 0 1.8T 0 disk
sdg 8:96 0 1.8T 0 disk
sdh 8:112 0 1.8T 0 disk
sdi 8:128 0 1.8T 0 disk
/usr/bin/lsblk -P -o NAME,MODEL,SERIAL,SIZE,TRAN,VENDOR,HCTL,TYPE,FSTYPE,LABEL,UUID
NAME=“sda” MODEL=“SATA SSD " SERIAL=“omitted” SIZE=“223.6G” TRAN=“ata” VENDOR=“ATA " HCTL=“2:0:1:0” TYPE=“disk” FSTYPE=”” LABEL="" UUID="“
NAME=“sda1” MODEL=”" SERIAL="" SIZE=“500M” TRAN="" VENDOR="" HCTL="" TYPE=“part” FSTYPE=“ext4” LABEL="" UUID=“8483a4b0-d796-4f5e-9321-d758436a5d0b"
NAME=“sda2” MODEL=”" SERIAL="" SIZE=“7.9G” TRAN="" VENDOR="" HCTL="" TYPE=“part” FSTYPE=“swap” LABEL="" UUID=“d7c5b6cf-2ebe-4db4-8b6b-83e92a14210f"
NAME=“sda3” MODEL=”" SERIAL="" SIZE=“215.2G” TRAN="" VENDOR="" HCTL="" TYPE=“part” FSTYPE=“btrfs” LABEL=“rockstor_rockstor” UUID=“f762a9a0-7066-4712-a380-f322591517d3"
NAME=“sdb” MODEL=“9750-8i DISK " SERIAL=“omitted” SIZE=“1.8T” TRAN=”” VENDOR=“LSI " HCTL=“0:0:0:0” TYPE=“disk” FSTYPE=”" LABEL="" UUID="“
NAME=“sdc” MODEL=“9750-8i DISK " SERIAL=“omitted” SIZE=“1.8T” TRAN=”” VENDOR=“LSI " HCTL=“0:0:1:0” TYPE=“disk” FSTYPE=”" LABEL="" UUID="“
NAME=“sdd” MODEL=“9750-8i DISK " SERIAL=“omitted” SIZE=“1.8T” TRAN=”” VENDOR=“LSI " HCTL=“0:0:2:0” TYPE=“disk” FSTYPE=”" LABEL="" UUID="“
NAME=“sde” MODEL=“9750-8i DISK " SERIAL=“omitted” SIZE=“1.8T” TRAN=”” VENDOR=“LSI " HCTL=“0:0:3:0” TYPE=“disk” FSTYPE=”" LABEL="" UUID="“
NAME=“sdf” MODEL=“9750-8i DISK " SERIAL=“omitted” SIZE=“1.8T” TRAN=”” VENDOR=“LSI " HCTL=“0:0:4:0” TYPE=“disk” FSTYPE=”" LABEL="" UUID="“
NAME=“sdg” MODEL=“9750-8i DISK " SERIAL=“omitted” SIZE=“1.8T” TRAN=”” VENDOR=“LSI " HCTL=“0:0:5:0” TYPE=“disk” FSTYPE=”" LABEL="" UUID="“
NAME=“sdh” MODEL=“9750-8i DISK " SERIAL=“omitted” SIZE=“1.8T” TRAN=”” VENDOR=“LSI " HCTL=“0:0:6:0” TYPE=“disk” FSTYPE=”" LABEL="" UUID="“
NAME=“sdi” MODEL=“9750-8i DISK " SERIAL=“omitted” SIZE=“1.8T” TRAN=”” VENDOR=“LSI " HCTL=“0:0:7:0” TYPE=“disk” FSTYPE=”" LABEL="" UUID=""
